Add files via upload

filetypes.abaqus

@@ -0,0 +1,79 @@
+# For complete documentation of this file, please see Geany's main documentation
+[styling]
+# Edit these in the colorscheme .conf file instead
+default=default
+comment=comment_line
+number=number
+string=string_1
+operator=operator
+processor=preprocessor
+starcommand=keyword
+argument=parameter
+
+[keywords]
+# all items must be in one line
+starcommands=amplitude base motion beam section boundary buckle cflux change contact type change friction change material change plastic change solid section change surface behavior 
+clearence cload complex frequency conductivity contact file contact output contact pair contact print controls correlation length coupled temperature-displacement coupling 
+crack propagation creep cyclic hardening cyclic symmetry model damping dashpot deformation plasticity density depvar design response design variables dflux 
+distributing distributing coupling distribution dload dsload dynamic elastic electrical conductivity electromagnetics element element output el file el print elset 
+end step equation expansion feasible direction filter film fluid constants fluid section frequency gap gap conductance gap heat generation geometric constraint geometric tolerances 
+green hcf heading heat transfer hyperelastic hyperfoam include initial conditions initial mesh initial strain increase konematic magnetic permeability mass mass flow 
+material matrix assemble membrane section modal damping modal dynamic modal change mohr coulomb mohr coulomb hardening mpc network mpc no analysis nodal thickness 
+node node file node output node print normal print normal nset objective orientation physical constants plastic pre-tension section radiate rate dependent refine mesh 
+restart retained nodal dofs rigid body robust design section print select cyclic symmmetry modes sensitivity shell section solid section specific gas constant specific heat spring static 
+steady state dynamics step submodel substructure generate substructure matrix output surface surface behavior surface interaction temperature tie time points transform 
+uncoupled temperature-displacement user element user material values at infinity viewfactor visco 
+arguments=2d 3d elset material name stiffness file mass file nset output section forces section type generate perturbation nlgeom storage absolute zero stefan boltzmann newton gravity 
+inc input incf frequencyf op amplitude film amplitude film time delay time delay time reset time points time reset total time at start last iterations contact elements load case 
+user add fixed submodel step data step data set file bstep mass flow coriolis steady state compressible turbulence model shallow water node surface element compressible shock smoothing 
+manning constants constraint name composite edge preservation direction weighting totals no heat transfer limit orientation offset offset1 offset2 nodal thickness solver submodel 
+to node to surface to massless interaction type zero small sliding adjust master slave value sector omega omega0 pressure-overclosure parameters reset ref node rot node direct 
+alpha deltmx magnetostatics material length law n ngraph tie elset matrix check alpha beta structural direct rayleigh explicit relative to absolute remove remove all method 
+boundary weighting edge preservation direction weighting oil liquid storage global cycmpc mode mission step max cycle scaling arruda-boyce mooney-rivlin neo hoke ogden polynomial 
+reduced polynomial yeoh plane straight beam dist constrained stiffness file radiation amplitude radiation time delay envnode cavity read write write only no change sorted random field only 
+nmin nmax nonlinear harmonic thermal network file name output file position tolerance integration points maxdof nodes cetol system
+[settings]
+# default extension used when saving files
+extension=inp
+
+# the following characters are these which a "word" can contains, see documentation
+#wordchars=_abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789
+
+# single comments, like # in this file
+comment_single=**
+# multiline comments
+#comment_open=
+#comment_close=
+
+# set to false if a comment character/string should start at column 0 of a line, true uses any
+# indentation of the line, e.g. setting to true causes the following on pressing CTRL+d
+	#command_example();
+# setting to false would generate this
+#	command_example();
+# This setting works only for single line comments
+comment_use_indent=false
+
+# context action command (please see Geany's main documentation for details)
+context_action_cmd=
+
+[indentation]
+#width=4
+# 0 is spaces, 1 is tabs, 2 is tab & spaces
+#type=1
+
+
+[build_settings]
+# %f will be replaced by the complete filename
+# %e will be replaced by the filename without extension
+# (use only one of it at one time)
+compiler=
+run_cmd=ccx "%e"
+
+[build-menu]
+FT_00_LB=Datacheck
+FT_00_CM=cgx -c "%f"
+FT_00_BD=false
+FT_01_LB=Run Job
+FT_01_CM=cgx -v "%e".frd
+FT_01_BD=false
+