Main nss sync 210125 #184
Merged
Main nss sync 210125 #184
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Apply the equivalent of commit f64541d ("realtek: HPE 1920 8G PoE+ 180W move fans to hwmon") to the 24-ports variants of the HPE 1920 PoE+ switches, with model numbers JG925A and JG926A. Copy from the original commit message: Move to using hwmon and gpio-fan. This is by adding gpio_fan_array to DTS and kmod-hwmon-gpiofan to DEVICE_PACKAGES. In combination with the new rtl8231 gpio driver the default fan behaviour will be maximum fan speed. Bump compat value to 1.1 due to existing config in /etc/config/system via gpio_switch. Also notify in device compat that fan is now going to be at bootloader setting (maximum in this case) by default unless turned down. As the init script 03_gpio_switches does not perform any action after removing these devices from it, the file can be dropped. Link: openwrt#17598 Signed-off-by: Fabian Groffen <grobian@gentoo.org> Signed-off-by: Sander Vanheule <sander@svanheule.net>
regmap_read_poll_timeout() relies on usleep_range() to time the polling
loop. With the current, rather large, scheduling interval, a short
usleep_range() may take a lot longer than expected, causing performance
issues.
Switch the driver over to using regmap_read_poll_timeout_atomic(), which
uses udelay() to time the polling loop.
For comparision, the 'ethtool -m <dev>' command is about 10 times faster
with the atomic variant.
Using 'perf -r10 ethtool -m lan25':
- Driver using regmap_read_poll_timeout():
2.0117 +- 0.0118 seconds time elapsed ( +- 0.58% )
- Driver using regmap_read_poll_timeout_atomic():
0.1674 +- 0.0250 seconds time elapsed ( +- 14.95% )
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some platforms a single ethernet device for all ports with multiple rx rings and NAPI threading enabled. In this case, the steering script was limiting performance by keeping all NAPI threads assigned to the same CPU. Fix this by assigning each rx queue and the corresponding NAPI task separately. Additionally, if the number of rx queues is at least as big as the number of CPUs, skip weight based assignment and distribute the load across all CPUs directly. Fixes: openwrt#17611 Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
fb3c2343b17b add support for an override config directory Signed-off-by: Felix Fietkau <nbd@nbd.name>
…ates This also includes a script to use the functionality from the command line Signed-off-by: Felix Fietkau <nbd@nbd.name>
The patch adding temperature sensor support for r8169 has been removed upstream and the functionality will be added to Realtek PHY instead: torvalds/linux@1f691a1 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Adds patches for the temperature sensor on RTL822x. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Import patches to fix several issues with status reporting of RealTek 2.5G PHYs. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
These patches have been accepted, so we can move them from pending to backported. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport ETS patch for Airoha ethernet and refresh affected patches. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending PCI patch that should correctly fix mediatek driver with Airoha SoC. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add some missing documented or commonly used values Fixes: openwrt#17431 Signed-off-by: Felix Fietkau <nbd@nbd.name>
For RTL839x, the driver was producing frequent timeouts on bus accesses. Increasing the timeout to the one from a recent Realtek SDK resolves these timeouts. To minimize overhead on different SoCs, each controller can specify their own timeout. This also add support for the register format as used on RTL93xx. Support is added for the RTL930x "ext gpio" controller. Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enable the driver for the Realtek Otto auxiliary MDIO driver so RTL839x devices can use it. The related node is added to the base devicetree for rtl839x-based devices, so they can enabled and use it when required. Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enable the RTL8231 MFD core driver, as well as the pinctrl/gpio driver to allow RTL839x devices to use it. Signed-off-by: Sander Vanheule <sander@svanheule.net>
Switch the Zyxel GS1900-48 over to the new MDIO-based driver for the RTL8231 GPIO expander. Signed-off-by: Sander Vanheule <sander@svanheule.net>
Currently, 2.5G port LED-s on Dynalink are incorrectly configured and thus they will light up all of the time. So, lets fix this by: 1. Current green LED is actually yellow, change the color 2. Fix its polarity as its actually active-low 3. The yellow LED that was registered as being connected to LED_1 pin on the PHY is not actually connected at all, so remove it. 4. The actual green LED is connected to LED_2 on the PHY so add it. Fixes: 75ad5c2 ("qualcommax: switch to qca8081 upstream PHY driver") Fixes: openwrt#14502 Link: openwrt#17656 Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 916af73. It was reported this change did not fix the reboot issues on AR9344. Signed-off-by: David Bauer <mail@david-bauer.net>
According to datasheet, on AR9344 the switch and switch analog need to be reset first before initiating a full reset. Resetting these systems fixes spurious reset hangs on Atheros AR9344 SoCs. Link: freifunk-gluon/gluon#2904 Signed-off-by: David Bauer <mail@david-bauer.net>
Some VRX518 modems fail to initialize properly with the error message "dc_ep_clk_on failed". As a result, the DSL data path doesn't work. This hack, which is based on code from the FRITZ!Box 7530 GPL archive, fixes the issue. It changes the PCIe vendor/device ID to values matching a Lantiq SoC. It also appears to emulate a Lantiq CPU ID register for connected PCIe devices, by remapping the matching address area to a specially crafted buffer using the address translation unit. A dedicated compatible is created to activate this in the device tree, so this shouldn't affect any devices other than FRITZ!Box 7530/7520. Original investigation was done in janh@59f5212 which used the "avm,host_magic" property to enabled the patch. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Florian Maurer <f.maurer@outlook.de> Link: openwrt#17622 Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix the name used for the transition image from Cudy. This should make it possible to use the cudy transition image. Fixes: 9d66b8b ("mediatek: filogic: Add support for cudy wr3000h") Link: openwrt#17652 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The WAX220 does have a 2.4GHz and 5GHz wifi led, which was set to trigger on netdev before. This commit changes this to trigger on activity of the respective radio Signed-off-by: Florian Maurer <f.maurer@outlook.de> Link: openwrt#17627 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
As per @KanjiMonster comment: st1202_dt_init() calls devm_led_classdev_register_ext() before the internal data structures are properly setup, so the leds become visible to user space while being partially initialized, leading to a window where trying to access them causes a NULL pointer access. Move devm_led_classdev_register_ext() to the last thing to happen during initialization. Signed-off-by: Manuel Fombuena <fombuena@outlook.com> Link: openwrt#17543 Signed-off-by: Robert Marko <robimarko@gmail.com>
Update handling of macro __assign_str() to also support the one-argument variant when building against kernel 6.10 or later. This is needed for building the next LTS kernel 6.12. Fixes: 384d079 ("mac80211: update to version 6.11") Signed-off-by: Tony Ambardar <itugrok@yahoo.com> Link: openwrt#17456 Signed-off-by: Robert Marko <robimarko@gmail.com>
Version 6.11 - October 8, 2024 * Feature: cmis: print active and inactive firmware versions * Feature: flash transceiver module firmware (--flash-module-firmware) * Feature: add T1BRR 10Mb/s mode to link mode tables * Feature: support for disabling netlink from command line * Fix: fix lanes parameter format specifier * Fix: add missing clause 33 PSE manual description * Fix: qsf: Better handling of Page A2h netlink read failure * Fix: rss: retrieve ring count using ETHTOOL_GRXRINGS ioctl (-x) * Misc: man page formatting fix * changelog here: https://git.kernel.org/pub/scm/network/ethtool/ethtool.git/commit/NEWS?id=c0ea4b70c71334ef038f7a3416b228a50dada406 Tested on gl.inet MT6000, retrieve ring count is now working Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com> Link: openwrt#17607 Signed-off-by: Robert Marko <robimarko@gmail.com>
initramfs for some devices grew so big, that it can't be loaded within the previous 32MB RAM limit. Make the LZMA_TEXT_ADDRESS configurable per-target once again, to fix it for bigger devices, while maintaining compatibility with previous ones. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> Link: openwrt#17616 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that LZMA_TEXT_START is configurable per-target once again, move the target above 32MB boundary for ZTE MF28* devices. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> Link: openwrt#17616 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Define EX5601-T1 and T-56 as alternative name, to explicitly show the device is supported using existing image. EX5601-T1 does not have the option to switch between WAN/SFP port. The switch port is hardwired to the WAN port. The Zyxel T-56 is the odido-branded version of the EX5601-T1. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Link: openwrt#17615 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The image size has been changed to prevent failures in routers and bootloop when flashing a large image using a stock bootloader. The LED trigger package has been removed for 1910, which is no longer in use. Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru> Link: openwrt#17630 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
…tions - Added detailed build instructions for new users, including the use of `scripts/env` for reproducible builds. - Updated comments to provide context for each config setting and package. - Clarified steps for selecting target devices and running make commands. - Included notes on SSL preferences, performance optimizations, and optional packages. - Removed redundant or unnecessary package entries for improved readability. Signed-off-by: Sean Khan <datapronix@protonmail.com>
Rather than pollute `qca-nss-ecm` with logic specific to ath11k, move into its own hotplug script managed by mac80211. Also enforce `qca-nss-ecm` dependency. Signed-off-by: Sean Khan <datapronix@protonmail.com>
Improve NSS event callback ihandling for better clarity and type safety This patch modifies ath11k_nss_wifili_event_receive to take a context parameter , enhancing code clarity by explicitly passing the ath11k_base. A wrapper function, ath11k_nss_wifili_ext_callback_wrapper, retrieves the ath11k_base from the net_device's private data, ensuring correct context handling. Signed-off-by: Sean Khan <datapronix@protonmail.com>
Signed-off-by: Sean Khan <datapronix@protonmail.com>
The firmware for 'ct' does not support ethernet frames, which is required for partial offload with mac80211 Signed-off-by: Sean Khan <datapronix@protonmail.com>
Mistakenly edited the patch by hand thinking I had incorrectly imported it from @bs. Original patch was throwing ``` peer.c:572:1: error: label at end of compound statement is a C23 extension ``` Moved spin_unlocks into exit as that's what it would have been doing anyways. Signed-off-by: Sean Khan <datapronix@protonmail.com>
Initial README for the example scripts/configs. Right now it's only for VLAN setup. Signed-off-by: Sean Khan <datapronix@protonmail.com>
* 802.11 k/v/r now fully works in sae-mixed mode. So we can now switch from psk2 (WPA2) to WPA2/WPA3 mixed mode. * Clean up uncessary configs * Remove WDS example as it's not applicable in this example Signed-off-by: Sean Khan <datapronix@protonmail.com>
Change "GRO FRAG" to "Interface" to account for additional information of other interface features (i.e. tx-checksumming) Signed-off-by: Sean Khan <datapronix@protonmail.com>
- fix issue #15: minor config mistake in the new nss setup vlan readme guide - fix formatting of primary subsection displaying too large. Signed-off-by: Sean Khan <datapronix@protonmail.com>
There is a null pointer bug caused by inconsistent handling of the `ath11k_base` structure. Previously, functions accessing `ar->ab` internally, assumed it was always valid. If `ar->ab` was not properly initialized, this led to null pointer dereferences. This patch resolves the issue by: - Explicitly passing `struct ath11k_base *ab` to functions that require it, instead of relying on `ar->ab`. - Replacing all instances of `ar->ab` with `ab` for direct access. Patch by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Sean Khan <datapronix@protonmail.com> (cherry picked from commit 1f6f55f9c737ece5e3d8156bbe280f84ea4bd480)
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Rebased against upstream commit 87033 mac80211: improve single-wiphy multi-radio support Signed-off-by: Sean Khan <datapronix@protonmail.com> ath11k_nss: Refresh patches against rebase 53eab61 Author: Felix Fietkau <nbd@nbd.name> AuthorDate: Mon Nov 18 11:21:02 2024 +0100 Commit: Felix Fietkau <nbd@nbd.name> CommitDate: Mon Nov 18 11:44:44 2024 +0100 mac80211: backport some upstream fixes Fix various issues, including potential crashes Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sean Khan <datapronix@protonmail.com> ath11k_nss: Fix patches for backports 6.12.6 Signed-off-by: Sean Khan <datapronix@protonmail.com> ath11k_nss: Refresh patches for backports 6.12.6 Signed-off-by: Sean Khan <datapronix@protonmail.com>
Patch resolves issues where certain brodcast frames like ARP or mDNS are not reliably transmitted after GTK key exchange. Signed-off-by: Sean Khan <datapronix@protonmail.com>
Signed-off-by: Sean Khan <datapronix@protonmail.com>
…ion for MX4200/MX5300/MX8500 Dual firmware devices like Linksys MX4200, MX5300 and MX8500 use separate rootfs partition. This option helps to keep all configuration during upgrade. Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
…nt partition Add new option to be able to perform upgrade on current partition for dual firmware devices: "-s stay on current partition (for dual firmware devices)" Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Thanks for your contribution to OpenWrt!
To help keep the codebase consistent and readable,
and to help people review your contribution,
we ask you to follow the rules you find in the wiki at this link
https://openwrt.org/submitting-patches
Please remove this message before posting the pull request.