Legacy I2S API

Espressif is retiring the legacy I2S API. So with Arduino ESP32 3.0.0 (which is based on IDF 5.1) this legacy API will not be available any more.

You can still use it in the older Arduino ESP32 2.0.x core releases.

A2DP Sink (Music Receiver)

This can be used e.g. to build your own Bluetooth Speaker.

A Simple I2S Example (A2DS Sink) using default Pins

Here is the simplest example which just uses the proper default settings:

#include "BluetoothA2DPSink.h"

BluetoothA2DPSink a2dp_sink;

void setup() {
    a2dp_sink.start("MyMusic");
}

void loop() {
}

This creates a new Bluetooth device with the name “MyMusic” and the output will be sent to the following default I2S pins which need to be conected to an external DAC:

• bck_io_num = 26
• ws_io_num = 25
• data_out_num = 22

Defining Pins

You can define your own pins easily by calling the set_pin_config method in the setup before the start.

#include "BluetoothA2DPSink.h"

BluetoothA2DPSink a2dp_sink;

void setup() {
    i2s_pin_config_t my_pin_config = {
        .mck_io_num = I2S_PIN_NO_CHANGE,
        .bck_io_num = 26,
        .ws_io_num = 25,
        .data_out_num = 22,
        .data_in_num = I2S_PIN_NO_CHANGE
    };
    a2dp_sink.set_pin_config(my_pin_config);
    a2dp_sink.start("MyMusic");
}

void loop() {
}

Using your specific i2s_config

In some cases you might want to use your specific i2s_config settings. E.g. to request a different bits_per_sample (e.g. 32) or to use the use_apll or to optimize the dma buffer...

#include "BluetoothA2DPSink.h"

BluetoothA2DPSink a2dp_sink;

void setup() {

    static i2s_config_t i2s_config = {
      .mode = (i2s_mode_t) (I2S_MODE_MASTER | I2S_MODE_TX),
      .sample_rate = 44100, // updated automatically by A2DP
      .bits_per_sample = (i2s_bits_per_sample_t)32,
      .channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
      .communication_format = (i2s_comm_format_t) (I2S_COMM_FORMAT_STAND_I2S),
      .intr_alloc_flags = 0, // default interrupt priority
      .dma_buf_count = 8,
      .dma_buf_len = 64,
      .use_apll = true,
      .tx_desc_auto_clear = true // avoiding noise in case of data unavailability
  };
  a2dp_sink.set_i2s_config(i2s_config);
  a2dp_sink.start("MyMusic");
}

void loop() {
}

Output to the Internal DAC

You can also send the output directly to the internal DAC of the ESP32 by providing the corresponding i2s_config:

#include "BluetoothA2DPSink.h"

BluetoothA2DPSink a2dp_sink;

void setup() {
    static const i2s_config_t i2s_config = {
        .mode = (i2s_mode_t) (I2S_MODE_MASTER | I2S_MODE_TX | I2S_MODE_DAC_BUILT_IN),
        .sample_rate = 44100, // corrected by info from bluetooth
        .bits_per_sample = (i2s_bits_per_sample_t) 16, /* the DAC module will only take the 8bits from MSB */
        .channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
        .communication_format = (i2s_comm_format_t)I2S_COMM_FORMAT_STAND_MSB,
        .intr_alloc_flags = 0, // default interrupt priority
        .dma_buf_count = 8,
        .dma_buf_len = 64,
        .use_apll = false
    };

    a2dp_sink.set_i2s_config(i2s_config);
    a2dp_sink.start("MyMusic");

}

void loop() {
}

The output goes now to the DAC pins GPIO25 (Channel 1) and GPIO26 (Channel 2).

Legacy API and External DAC

Here is the link to the legacy information