Replies: 34 comments 2 replies
-
|
Confirmed. Looks like the flash works just once and is disabled til next reset. Found no workaround. I'll roll back ... |
Beta Was this translation helpful? Give feedback.
-
|
Might be the same issue as on #3338 |
Beta Was this translation helpful? Give feedback.
-
|
I can reproduce the error with firmware v15.7.0 and webinterface 16.0.0-RC4 |
Beta Was this translation helpful? Give feedback.
-
|
Same problem. Can't set reference image properly |
Beta Was this translation helpful? Give feedback.
-
Which version was you flash working fine before? I see above my previous comment that problem was already present in previous release version 15.7.0 |
Beta Was this translation helpful? Give feedback.
-
|
@SGXander If you want you can try this firmware (16.0.0-RC4 + fix): https://github.com/SybexX/AI-on-the-edge-device/actions/runs/11874812323/artifacts/2197416682 |
Beta Was this translation helpful? Give feedback.
-
|
sorry for not updating, I rolled back to 15.7.0 too and it was ok there so I stuck with that. I also have an external flash too now and it's been fine. I'll look to update this weekend and see if the issue returns. |
Beta Was this translation helpful? Give feedback.
-
|
There was no change in the LED implementation/Control between versions 15.4.0, 15.7.0 and 16.0.0-RC4. |
Beta Was this translation helpful? Give feedback.
-
|
It's the other way round for me, I started with 16.0.0-RC4 as it was the top release and then realised it was RC so rebuilt the ESP32-CAM with 15.7.0 |
Beta Was this translation helpful? Give feedback.
-
|
@SGXander Did you have Auto-Exposure Control and Auto-Exposure Control 2 ("night mode") activated in both versions? |
Beta Was this translation helpful? Give feedback.
-
|
can't say for certain before/on 16.0.0-RC4 but on my running version 15.7.0 it looks like this (believed default as I've not touched it) |
Beta Was this translation helpful? Give feedback.
-
|
Hello, Any ideas and/or updates ? Steve Bee |
Beta Was this translation helpful? Give feedback.
-
|
@doncorso please try this firmware: https://github.com/SybexX/AI-on-the-edge-device/actions/runs/11875592284/artifacts/2197579082 It would also be helpful if you described the exact procedure (what did you do and what files did you use, previous version or new installation............) as there are several ways to install and update AI-on-the-edge-device. |
Beta Was this translation helpful? Give feedback.
-
|
I have this issue on a brand new installation. |
Beta Was this translation helpful? Give feedback.
-
|
Is the LED really not turning on or are you just assuming it because the picture is dark? remote-setup:
manual-setup:
update:
|
Beta Was this translation helpful? Give feedback.
-
|
might be related to: #3471 |
Beta Was this translation helpful? Give feedback.
-
|
Same here, following. Update to RC5 brings errors about camera or just stucks on delayed start. |
Beta Was this translation helpful? Give feedback.
-
|
@PsYcHLT Did you only select the firmware.bin or the entire AI-on-the-edge-device__update__v16.0.0-RC5.zip when updating? |
Beta Was this translation helpful? Give feedback.
-
I used full update zip file over OTA functionallity. So basically I just started using this app, and I love the idea and how it works so far! I have two ESP32 CAM devices, both were with 16.4RC version and both had same issue. One upgraded to 16.5RC - was not working properly, so downgraded to 15.7, everything seemed to be fine, but lately just wanted to give a one more try for 16.5 and now it don't even connect to the network :) Just to mention, always were using OTA functionality, I think I got to the point when I will have to dissasembly everything and flash it again to 15.7, or maybe version you have sent. |
Beta Was this translation helpful? Give feedback.
-
|
@PsYcHLT A lot of things have been fixed in the main version. |
Beta Was this translation helpful? Give feedback.
-
|
@SybexX I'm getting this page in my browser, I think I'll also scan sd card for bads as I used some old scrap cards from back when 32GB sd card was really expensive 😆
|
Beta Was this translation helpful? Give feedback.
-
|
Same here. 15.7 works just fine for a long time. Tried the AI-on-the-edge-device__update__v16.0.0-RC5.zip to get the "measurement" state for raw in home assistant. It installed fine and worked first. |
Beta Was this translation helpful? Give feedback.
-
|
Ah ... just noticed ... the file system on the SDCard is bad. I checked it and the card itself is physically fine. It is the file system. So, maybe worth to check the source code for things like: file does not get closed properly once data has been written. Or a reboot gets executed while still writing a file, foo, bla... |
Beta Was this translation helpful? Give feedback.
-
|
@mesistostefre what filesystem you are using? NTFS? So it was OK for older versions but for newer it must be FAT32? |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
|
FAT ... and now the whole thing (16 RC5) works for me. |
Beta Was this translation helpful? Give feedback.
-
|
Well, seems like my case is much weirder, no bads, card is FAT32. Will try @SybexX suggested version in a moment |
Beta Was this translation helpful? Give feedback.
-
|
Ended up fully reflashing it to 15.7 and then upgraded to last commit version of main branch. Seems to be working fine, also when taking reference image it turns on the LED now. WIll need more time to test it fully, but happy bunny for now 😸 |
Beta Was this translation helpful? Give feedback.
-
|
Here we go again... So it was working fine, until I have painted my points of interest and restarted... So live video was working, I have aligned it, took a reference image (this time it turned flashlight), painted ROIs and boom... |
Beta Was this translation helpful? Give feedback.
-
|
It will be not a discussion but my brain dump 😆 Changed power supply and it works again. Maybe that was the real issue after all |
Beta Was this translation helpful? Give feedback.
-
|
Am using a calibrated external power supply, not one of these plugs. It certainly was not the power supply in my case. |
Beta Was this translation helpful? Give feedback.
-
|
Same problem as @SGXander, only without an error message in the log. Only firmware 16.0.0-RC4 with web interface 15.7.0 solves the problem. Unfortunately, the combination causes the problem that settings made via the web interface apparently write settings that are no longer valid in firmware 16 into the .ini. This can only be avoided by editing the ini file directly. |
Beta Was this translation helpful? Give feedback.
-
The Problem
after alignment step 1, step 2 appears to disable the flash and use the rear LED on the board. This behaviour continues until the ESP is reset, where it works for alignment again but then breaks on step 2 repeatably
Version
16.0.0-RC4
Logfile
Expected Behavior
clicking create new reference button should produce the same image as alignment
Screenshots
Additional Context
the ESP must be reset to restore flash functionality during alignment but the issue is repeatable
Beta Was this translation helpful? Give feedback.
All reactions