ST-Link Flashing

[felau]

Greetings!

I have been trying multiple times on different computers to update my existing BlueSCSI to the lastest firmware. I bought the ST-Link V2 after the fact to perform that exact task.

Here is where i bought it :
https://www.amazon.ca/gp/product/B09JMQS68W/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1

I performed all the tasks required (Including the driver update), but it seems like its not doing anything.

My USB cable is correct, i see the device appear in device manager when i connect it.

I noticed that the original IDs for the device in the Batch file are 0x1eaf:0x003, but in device manager i see that it is 0x1eaf:0x004 so I tried to change that in the batch file, but it doesn't help.

Here is the log. Anything obvious?

Thank you very much in advance!

-------------------------------------
  ____  _             _____  _____  _____ _____
 |  _ \| |           / ____|/ ____|/ ____|_   _|
 | |_) | |_   _  ___| (___ | |    | (___   | |
 |  _ <| | | | |/ _ \\___ \| |     \___ \  | |
 | |_) | | |_| |  __/____) | |____ ____) |_| |_
 |____/|_|\__,_|\___|_____/ \_____|_____/|_____|

     Welcome to the BlueSCSI Firmware BBS!
          Flasher Version 2022-04-11

Choose an option:

[1] Upgrade via USB.
 - You must have BlueSCSI v1.1-20220404-USB or greater already flashed.
[2] Prepare a blank BluePill or older BlueSCSI firmware for USB support.
 - You must have a STLink v2.

[H] Help
[P] Page Sysop
[Q] Hang Up

Choice?2
Flashing the generic_boot20_pc13.bin
* Move BOOT0 to 1 (Jumper furthest from the RESET button on the BluePill)
* Connect the ST-LinkV2 to your BlueSCSI and connect it to your computer.
Press any key to continue . . .
Starting flash...
NOTE: Some BulePills can take up to 2 minutes to flash.
xPack OpenOCD x86_64 Open On-Chip Debugger 0.11.0+dev (2022-03-25-17:32)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.org/doc/doxygen/bugs.html
0
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
Info : DEPRECATED target event trace-config; use TPIU events {pre,post}-{enable,disable}
Warn : Transport "hla_swd" was already selected
hla_swd
Info : clock speed 1000 kHz
Check output if successful (Windows...)
* Move the BOOT0 Jumper back to position 0
* Disconnect the BlueSCSI from the STLink
Ready to flash BlueSCSI firmware.
Press any key to continue . . .
Flashing BlueSCSI-v1.1-20220404-USB.bin
* Move BOOT1 to 1 (Jumper nearest the RESET button on the BluePill)
* Connect via USB to the BluePill
dfu-util 0.11

Copyright 2005-2009 Weston Schmidt, Harald Welte and OpenMoko Inc.
Copyright 2010-2021 Tormod Volden and Stefan Schmidt
This program is Free Software and has ABSOLUTELY NO WARRANTY
Please report bugs to http://sourceforge.net/p/dfu-util/tickets/

Warning: Invalid DFU suffix signature
A valid DFU suffix will be required in a future dfu-util release
Waiting for device, exit with ctrl-C

[felau]

You may delete my request, i managed to perform the flashing using PlatformIO. Thank you.

[erichelgeson]

PlatformIO uses the same mechanism to flash as Option 2 - Step 1. If you flashed via PlatformIO you will not have a USB Bootloader loaded. Also if you flashed the current main branch - it is currently in testing and not a stable release yet.

I would encourage you to go back and look at why OpenOCD failed - the logs don't even show it trying to flash - did you have the STLink connected to the bluepill and the jumpers set before you hit proceed?