DS1815+ and wisdPi 5gbe USB partial success

[mervincm]

DS 1815+ (avoton)
DS patched to date and was using your package 2.18x for the driver
Was using a plugables v1 realtek 2.5 (at 2.5Gbe) for many months without issue.
using monoprice 6 foot cat6a slim cable (tried 2)
Upgraded to the wisdPi WP-ut5 USB 3.2 to 5GbE adapter based on Realtek RTL8157 and deleted old package, installed new 2.19.2.-1 driver package. no command line action seemed required.

when connected to a 2.5G switch,
-displays 2500 in Synology network page
-displays speed:2500Mb/s when I do ethtool eth4 on the synology
-I see 220+ MB/sec file copy speed to/from NAS

when connected to a 10G switch (with 1/2.5/5/10 support) OR separate 10G switch (with SFP+ with 1/2.5/5/10 support)
-displays nothing in Synology network page
-displays speed: unknown when I do ethtool eth4 on the synology
-I see 113 MB/sec file copy speed to/from NAS
I am not sure about the LED color light scheme, so I can't confirm the actual connection speed but performance to this nas gives 113 copy speed on 1gbe links

it seems the driver version was updated
/$ ethtool -i eth4
driver: r8152
version: v2.19.2 (2024/10/21)
firmware-version:
expansion-rom-version:
bus-info: usb-0000:04:00.0-3
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no

on 2.5g switch
Settings for eth4:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
2500baseX/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
2500baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 2500Mb/s
Duplex: Full
Port: MII
PHYAD: 32
Transceiver: internal
Auto-negotiation: on
Cannot get wake-on-lan settings: Operation not permitted
Current message level: 0x00007fff (32767)
drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol
Link detected: yes

on 10g switch
Settings for eth4:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
2500baseX/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
2500baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Port: MII
PHYAD: 32
Transceiver: internal
Auto-negotiation: on
Cannot get wake-on-lan settings: Operation not permitted
Current message level: 0x00007fff (32767)
drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol
Link detected: yes

lsusb
|__usb1 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00: 16.0) hub
|__1-1 8087:07db:0002 09 2.00 480MBit/s 0mA 1IF ( ffffffd1ffffffb2 ffffffdbffffffad) hub
|__1-1.1 f400:f400:0100 00 2.00 480MBit/s 200mA 1IF (Synology DiskSt ation 650051DF8C31C948)
|__usb2 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.108 et xhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
|__usb3 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.108 et xhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
|__3-3 0bda:8157:3000 00 3.20 5000MBit/s 544mA 1IF (WisdPi USB 5G E thernet 000334C8D6B10E01)

dmesq portion
[ 118.321207] r8152: module verification failed: signature and/or required key missing - tainting kernel
[ 118.339194] usbcore: registered new interface driver r8152
[ 118.347680] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 1 ep 2 with no TDs queued?
[ 118.357739] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 1 ep 3 with no TDs queued?
[ 118.367616] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 1 ep 6 with no TDs queued?
[ 119.481116] usb 3-3: reset SuperSpeed USB device number 2 using etxhci_hcd-170202
[ 119.704022] r8152 3-3:1.0: ram code version is wrong 0000(0013
[ 120.651300] fuse init (API version 7.22)
[ 120.762526] r8152 3-3:1.0 eth4: v2.19.2 (2024/10/21)
[ 120.768112] r8152 3-3:1.0 eth4: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.

[ 120.785664] r8152 3-3:1.0 eth4: chip rev 19
[ 122.052154] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
[ 124.340657] IPv6: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
[ 124.352398] r8152 3-3:1.0 eth4: carrier on
[ 154.736723] Synotify use 16384 event queue size